• Avatar do Utilizador
  • Avatar do Utilizador
By alexmv
#184322
Boas, estou com dificuldades e fazer blind do taranis X9 Lite com o receptor R-XSR.

O TX está com o V.2.3.0
EEPR: 219
O módulo interno está na V. 1.1.0/1.1.3 FCC

Já flashei o RX com a versão que está no site (RXSR_ACCESS_190805.frk)

Mas quando vou para fazer blind apenas ficam ligados os 3 leds e não passa daí.

O que poderá estar errado?
By Brnmd
#184326
Carrega o firmware de novo para o R-XSR e tenta o bind de novo, estás a o fazer em D16?
By alexmv
#184332
Brnmd Escreveu:
18 set 2019, 14:21
Carrega o firmware de novo para o R-XSR e tenta o bind de novo, estás a o fazer em D16?
Boas. em ACCST D16 não consigo.. Apenas consegui em ACCESS. Mas no INAV não está a funcionar. Poderá ser por estar em ACCESS?
By Brnmd
#184333
@alexmv,

Seguiste estes passos todos?

Registration & Automatic binding (Smart Match )With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S" button.Follow the step below to finish the Registration & binding procedure:1. Put the transmitter/transmitter module into [Reg] status.1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODDEL SETUP-PAGE 2, choose Internal or Extermal RF, and select [Reg].2. Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED and GREEN LEDon the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED andGREEN LED will flash, and the transmitter displays [Registration ok].3. Turn off the receiver.4. Move the cursor to select the receiver1 [Bind].5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX, the GREEN will keep lit, and the transmitter displays [Bind successful].6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally.
By alexmv
#184336
Brnmd Escreveu:@alexmv,

Seguiste estes passos todos?

Registration & Automatic binding (Smart Match )With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S" button.Follow the step below to finish the Registration & binding procedure:1. Put the transmitter/transmitter module into [Reg] status.1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODDEL SETUP-PAGE 2, choose Internal or Extermal RF, and select [Reg].2. Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED and GREEN LEDon the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED andGREEN LED will flash, and the transmitter displays [Registration ok].3. Turn off the receiver.4. Move the cursor to select the receiver1 [Bind].5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX, the GREEN will keep lit, and the transmitter displays [Bind successful].6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally.
Em access já consegui ;)
Brnmd liked this
R9m+R9MM

Estou a utilizar o modulos R9m e o recetor r9mm no[…]

Joao Maia

A ver se começo a fazer mais vídeos.[…]

Contrução de um drones

Isso poderia ser uma excelente ideia, como poder[…]

SUP!!

Boas, bem vindo ao fórum!

Ajudem o fórum usando este link para compras na Banggood